Forum Index
Jeep Horizons HomeLinksJeep Horizons Tech Write-upsJeep newsLand useContact

 Watched TopicsWatched Topics   FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

question about a driveshaft


 
Post new topic   Reply to topic     Forum Index -> Grand Cherokee Forum
View previous topic :: View next topic  
Author Message
jeepzj9304
Member


Joined: 24 Apr 2005
Location: Indiana

PostPosted: Sat Oct 15, 2005 10:21 pm    Post subject: question about a driveshaft Reply with quote

i have a 3inch bb in the front and a 2 inch in the rear, now i am wanting to put a 3inch coils on top of that, i know every thing i need to do with the susp to make it work its just the drive shaft that has me confused. i dont want to get a TC drop due to the fact it decreases my break over angle. and if i need a cv driveshaft where can i get one cause i been searching and i cant find anything.
_________________
93 ZJ 4.0 I6
K&N insert
3" front BB
2" rear BB
31x11.5" Mickey Thompson Baja Claws
16"x10" 4.25 Backspacing Rockcrawler Rims
Back to top
View user's profile Send private message Visit poster's website AIM Address
Code3TJ
Hacker
Hacker


Joined: 01 Jan 2004
Location: Uzbekistan

PostPosted: Sun Oct 16, 2005 9:24 am    Post subject: Reply with quote

Did you check Tom Wood's? http://www.4xshaft.com/

edit: what transfer case do you have and do you have an SYE?
_________________
Nothing to see here.
Back to top
View user's profile Send private message
jeepzj9304
Member


Joined: 24 Apr 2005
Location: Indiana

PostPosted: Sun Oct 16, 2005 10:24 am    Post subject: Reply with quote

i have the 242 tc and no sye
_________________
93 ZJ 4.0 I6
K&N insert
3" front BB
2" rear BB
31x11.5" Mickey Thompson Baja Claws
16"x10" 4.25 Backspacing Rockcrawler Rims
Back to top
View user's profile Send private message Visit poster's website AIM Address
swamp boy
Cherokee Muderator
Cherokee Muderator


Joined: 01 Jan 2004
Location: New Orleans LA.

PostPosted: Sun Oct 16, 2005 6:35 pm    Post subject: Reply with quote

I am running RE 5.5 springs and stock shafts.. If anything with that much lift you are going to have to push your axle back because it will swing in and make your shaft to long....(no pun intended.. Mr. Green )

Other than that you should be fine..
_________________
BONE STOCK
Unless you include the sawzall work..

Back to top
View user's profile Send private message Send e-mail Visit poster's website MSN Messenger
Display posts from previous:   
Post new topic   Reply to topic     Forum Index -> Grand Cherokee Forum All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Visit links4jeeps.com for write-ups, forums and clubs




Jeep®, Wrangler, Cherokee, Liberty and Grand Cherokee are copyrighted and trademarked to Chrysler LLC.
jeephorizons.com is not in any way associated with or endorsed by the Chrysler LLC.
All other content is copyright Jeep Horizons 2004-2008.
Tech write-ups Links Discussion board Land use News Site Map Terms of Use

Powered by phpBB © 2001, 2005 phpBB Group